- Do you need a stud finder to hang pictures?
- What can I use if I don’t have a stud finder?
- Can I use my iPhone as a stud finder?
- Can I hang a picture with just a nail?
- How much weight can a drywall anchor hold?
- How do you know you hit a stud?
- How long should screws be for studs?
- Why do you need to find wall studs?
- Are you supposed to drill into studs?
- How far apart are wall studs?
- Can you mount a TV without studs?
- Why can’t I drill into stud?
- What happens if I drill into a wire?
Do you need a stud finder to hang pictures?
Get a stud finder.
While you may not need to hang light posters in acrylic or plastic frames or photographs from a stud, if you do have an expensive piece in a heavy frame, you should know where the studs behind your walls are..
What can I use if I don’t have a stud finder?
Measure from the Corner You can attempt the “knock test” near the corner to see if you can determine where the shorter stud-spacing might have been added. This is most effective if you’re measuring a corner of the exterior of the house, which is why it is the least effective way to find a stud without a stud finder.
Can I use my iPhone as a stud finder?
The iPhone beeps when its magnetometer, in the upper right of the phone, is near metal. Stud Find is an iPhone application that uses the device’s built-in magnetometer to find metal studs, screws, nails and anything metallic in a wall.
Can I hang a picture with just a nail?
Don’t use nails—well, not JUST nails. I’ll even admit there are several in my own home hung this way. But they are the pictures most likely to fall off the wall or require regular straightening. A single nail hammered into drywall is not stable enough to support much weight, so invest in the right hardware.
How much weight can a drywall anchor hold?
Toggles, anchors or molly bolts are surprisingly strong. A 1/8 toggle can hold 30 pounds on 1/2-inch drywall and a 3/8-inch toggle can handle a hefty 50 pounds or more safely. When applying any kind of drywall anchor, you should understand how they work and which screw anchor may work best to put into a hollow wall.
How do you know you hit a stud?
Make a fist and knock on the wall with your knuckles. In some places, you’ll hear a hollow sound. Other areas will sound more “solid.” The “solid” sound indicates you have knocked on a stud. Studs are located about 16 to 24-inches apart.
How long should screws be for studs?
You should use screws long enough to engage the stud one half the length of the screw. For example, if the wallboard is 5/8″ thick and the bracket is 1/8″ thick then you want a screw that is at least 1–1/2″ long.
Why do you need to find wall studs?
Why You Should Find Studs Studs are boards that function as framing elements in your home, supporting the walls. You may wonder, how far apart are studs in my home? They’re always spaced either 16 or 24 inches on-center (measured from center to center) along the wall and run between the floor and ceiling.
Are you supposed to drill into studs?
If you’re hanging shelves or mounting anything heavy to the wall, you’ll probably want to mount it directly to the wall studs. However, you should be drilling pilot holes first before driving in any screws.
How far apart are wall studs?
16 inchesThe general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.
Can you mount a TV without studs?
You can mount a TV without studs using anchors, toggle anchors, mounting plates, ceiling mounts, and other mounting options.
Why can’t I drill into stud?
A lot of wood screw and drywall screws won’t bite into metal studs and wiggle out. … As mentioned, nail plates or conduit or even structural steel might be behind the drywall. As for the bit, it will go through metal if it is sharp. Go slowly both drill speed and how hard you push.
What happens if I drill into a wire?
You drill into one conductor, almost severing it but not quite. Everything is fine until the cable is left carrying power near its rated capacity for an extended period, at which point the weak point gets hot. It might melt and cut the power, or if you are unlucky it arcs and sets fire to something.